Modding tricams

Lost gear? Selling? Donating? Questions?

Moderators: chossmonkey, Dom, granite_grrl

Modding tricams

Postby mick » Sun Jun 28, 2009 9:27 am

I made a minor modification to my tricams. Since the nylon stems/slings are so floppy, I cut two long, narrow rectangles of plastic from the side of a 2L pop bottle and taped them to the tricam sling on either side, thus giving it a bit more rigidity. I've found this gives me more control when making placements, and I was careful to leave enough of the sling exposed up by the head so that the tricam doesn't touch the plastic when it's folded back on itself or interfere with the action at all.

Is there any reason this is a bad idea or even unsafe somehow?

cheers
mick
ps. I can post a photo if my description is unclear
User avatar
mick
 
Posts: 399
Joined: Mon Aug 13, 2007 2:23 pm

Re: Modding tricams

Postby Murph » Sun Jun 28, 2009 11:15 am

Something like this...Viagra for tricams...lol, Seems like it should be safe unless there is some strange solvent in the glue of the tape Image
-"Why do this instead of a 5.13 sport climb?"
-"Cause this is way more bitch!n'"
Matt Segal, The sharp end
User avatar
Murph
 
Posts: 188
Joined: Mon Oct 02, 2006 9:46 pm

Re: Modding tricams

Postby mick » Sun Jun 28, 2009 11:54 am

I think scotch tape would have a pretty low solvent content :)

Is that some kind of shrink wrapping sleeve on your tricam there?
Any reason to leave the closer clipping point open in the sling between the 1st and 2nd bartacks? I've never seen a reason to clip there rather than at the back of the sling but I don't have that much experience.
User avatar
mick
 
Posts: 399
Joined: Mon Aug 13, 2007 2:23 pm

Re: Modding tricams

Postby Burley » Sun Jun 28, 2009 12:11 pm

Uuuhhggrr... Tricams.
Burley
 
Posts: 270
Joined: Mon Feb 27, 2006 1:37 pm
Location: Fredericton

Re: Modding tricams

Postby Adam » Sun Jun 28, 2009 1:26 pm

mick wrote:Any reason to leave the closer clipping point open in the sling between the 1st and 2nd bartacks? I've never seen a reason to clip there rather than at the back of the sling but I don't have that much experience.


never clip in above a bartack... if the biner comes under load it will slice right through the stiching.

only clip into the ends of dogbones for the same reason.
User avatar
Adam
 
Posts: 1105
Joined: Mon Apr 02, 2007 8:39 pm

Re: Modding tricams

Postby Fred » Sun Jun 28, 2009 6:53 pm

I think the stem is supposed to be soft to minimize potential for walking. A rigid stem might push the cam head around easily walking it around and falling out of position. Unlike CAMS the Tricams are not as forgiving if they move out of place since they are not spring loaded.

Note that this is a mute point if you plan to use long runners.
I want to go to hell... there's probably lots of rock to climb there.
User avatar
Fred
Site Admin
 
Posts: 3140
Joined: Wed Oct 20, 2004 12:30 am
Location: Fredericton, NB

Re: Modding tricams

Postby chossmonkey » Mon Jun 29, 2009 6:26 am

trad_reborn wrote:never clip in above a bartack... if the biner comes under load it will slice right through the stiching.

only clip into the ends of dogbones for the same reason.



Fred wrote:I think the stem is supposed to be soft to minimize potential for walking. A rigid stem might push the cam head around easily walking it around and falling out of position. Unlike CAMS the Tricams are not as forgiving if they move out of place since they are not spring loaded.

Note that this is a mute point if you plan to use long runners.



Correct and correct.
If women ruled the world there would be no wars, just be a bunch of jealous countries not talking to each other.
User avatar
chossmonkey
 
Posts: 1243
Joined: Mon Nov 13, 2006 4:11 pm
Location: Running a muck.

Re: Modding tricams

Postby *Chris* » Mon Jun 29, 2009 7:20 am

Fred wrote:I think the stem is supposed to be soft to minimize potential for walking. A rigid stem might push the cam head around easily walking it around and falling out of position. Unlike CAMS the Tricams are not as forgiving if they move out of place since they are not spring loaded
Clearly, you don't set those little buggers like I do!
Murph wrote:Something like this...Viagra for tricams...
Can we have this post 'content moderated'? The imagery is just too much for me! :oops:
User avatar
*Chris*
 
Posts: 848
Joined: Wed Apr 19, 2006 2:32 pm
Location: Fredericton

Re: Modding tricams

Postby Murph » Mon Jun 29, 2009 9:47 pm

trad_reborn wrote:
mick wrote:Any reason to leave the closer clipping point open in the sling between the 1st and 2nd bartacks? I've never seen a reason to clip there rather than at the back of the sling but I don't have that much experience.


never clip in above a bartack... if the biner comes under load it will slice right through the stiching.

only clip into the ends of dogbones for the same reason.


I've heard on other forums that an aid climber short clipped a tricam,to gain a higher reach and the bar tacks failed under body weight.
-"Why do this instead of a 5.13 sport climb?"
-"Cause this is way more bitch!n'"
Matt Segal, The sharp end
User avatar
Murph
 
Posts: 188
Joined: Mon Oct 02, 2006 9:46 pm

Re: Modding tricams

Postby Adam » Tue Jun 30, 2009 8:35 am

Murph wrote:I've heard on other forums that an aid climber short clipped a tricam,to gain a higher reach and the bar tacks failed under body weight.


i would have thought it would support body weight, but perhaps he bounce tested it or something. in either case they're not designed for that.

i was in RRG last year and some guy extended a quick draw by clipping a second one ABOVE the bar tack. i think i posted about it on here actually. he ended up taking a fall on it, and the quickdraw blew apart and he came another 15' down, flipped upside down, and hit his back on the rock. we were all in shock as to what happened and questioned the gear until we found out later how he had the draws set up...

good lesson!
User avatar
Adam
 
Posts: 1105
Joined: Mon Apr 02, 2007 8:39 pm


Return to Gear

Who is online

Users browsing this forum: No registered users and 1 guest

cron